Measurement frequency up to 100kHz
Test level 100 ~ 2000mV
Support the measurement of DC resistance and electrolytic capacitor
Internal bias voltage output (1mV-1500mV)
Automatic identification of component measurement
3.5-inch TFT display, 5 and a half bits display
USB, RS232 communication interface, Handle sorting
Data recording function (maximum and minimum values, average value)
Support SCPI communication protocol
Provide system settings, which can configure language, buzzer, screen brightness, etc according to the needs of users.
Basic accuracy 0.2%
Manual and automatic range
Be equipped with open circuit and short circuit correction
Comparator has sorting and alarm function
Provide a variety of test ports
Model | ET4401 | ET4402 | ET4410 | ET4501 | ET4502 | ET4510 |
Digits | Main parameter: 5 digits; secondary parameter: 5 digits |
Measurement Parameter | Main parameter: L/C/R/Z; secondary parameter: X/D/Q/θ/ESR |
Measurement Range(L) | 0.01μH - 9999H |
Measurement Range(C) | 0.01pF - 99999μF |
Measurement Range(R) | 0.0001Ω - 99.99MΩ |
Basic Accuracy | 0.2% |
Test Frequency (Hz) | 100~10kHz 10 point | 100~20kHz 12point | 100~100kHz 16 point | 10~10kHz 1Hz Stepping | 10~20kHz 1Hz Stepping | 10~100kHz 1Hz Stepping |
Measurement Display Speed | 2 times/second (slow), 4 times/second (medium speed), 8 times/sec (fast) |
Internal Bias | 0-1500mV adjustable, 1mV stepping |
Test Level | 100mV,300mV,600mV,1000mV,1500mV,2000mV | 0.1V~2V adjusted ,1mV Stepping |
Correction Function | Open circuit correction, short circuit correction |
Screening function | The screening limit can be set from -50% to + 50% with fixed points of 1%, 5%, 10% and 20% |
Selection of comparator | Five gear sorting, third gear qualified, one gear failed, one ancillary gear |
Communication Interface | Standard configuration: USB, RS232 (or 485), Handle interface; Optional: GPIB, USB Host |
Others | Support DCR, electrolytic capacitor measurement mode, adjustable backlight brightness, optional in English and Chinese |
Power connection
(1) Power supply voltage range: 220V AC ± 10%, or 110V AC ± 10%.
(2) Power supply frequency range: 45-65Hz.
(3) Phase line L, zero line N, and ground line E of power input shall be the same as those of the power plug of this instrument.
(4) The instrument has been carefully designed to reduce the clutter interference caused by the input at the AC power supply terminal. However, it shall be used in a low noise environment. If such is not the case, please install the power supply filter.
WARNING: In order to prevent leakage from causing damage to the instrument or person, the user must ensure that the ground line of the power supply is reliably connected to the earth.
(5) Power consumption: less than 20W.
1.1 General Technical Specifications
Power supply voltage: 220V AC ± 10%, or 110V AC ± 10%, 45-65Hz
Working environment: 0 ~ 40 ℃, relative humidity <80%.
Storage environment: -10 ~ 50 ℃, relative humidity <80%.
Dimensions: 265mm * 105mm * 305mm (width * height* depth).
Mass: 2.3kg.
Standard Accessories:
Four-terminal-pair Kelvin test cable (35A51).
Three-core power cord (30A51).
One User Manual.
Optional accessories:
RS232 serial cable / USB data cable.
Handle cable.
Four-terminal-pair Kelvin test fixture (including short block)
SMD component test fixture (including short block
